Sand Three Cylinder Rotary Dryer
Sand Rotary Dryer our products
- Drum Dryer machine;
- Three Cylinder Dryer;
- 5TPH Rotary Dryer;
- 10-15tph Rotary Dryer;
- 20-40tph Rotary Dryer.
Drying modes:
- Diesel
- Gasoline
- Coal
- Natural gas,marsh gas
| Modèle (mm) |
Inclination (%) |
Rotate speed (r/min) |
Air inlet temperature (° C) |
Power (kW) |
Production capacity (ème) |
Poids (t) |
| Φ 600×6000 | 3-5 | 3-8 | ≤ 700 | 3 | 0.5-1.5 | 2.9 |
| Φ 800×8000 | 3-5 | 3-8 | ≤ 700 | 4 | 0.8-2.0 | 3.5 |
| Φ 800×10000 | 3-5 | 3-8 | ≤ 700 | 4 | 0.8-2.5 | 4.5 |
| Φ 1000×10000 | 3-5 | 3-8 | ≤ 700 | 5.5 | 1.0-3.5 | 5.6 |
| Φ 1200×10000 | 3-5 | 3-8 | ≤ 700 | 7.5 | 1.8-5 | 14.5 |
| Φ 1200×12000 | 3-5 | 3-8 | ≤ 700 | 11 | 2-6 | 14.8 |
| Φ 1500×12000 | 3-5 | 2-6 | ≤ 800 | 15 | 3.5-9 | 17.8 |
| Φ 1800×12000 | 3-5 | 2-6 | ≤ 800 | 18 | 5-12 | 25 |
| Φ 2200×12000 | 3-5 | 1.5-6 | ≤ 800 | 18.5 | 6-15 | 33 |
| Φ 2200×18000 | 3-5 | 1.5-6 | ≤ 800 | 22 | 10-18 | 53.8 |
| Φ 2200×20000 | 3-5 | 1.5-6 | ≤ 800 | 30 | 12-20 | 56 |
| Φ 2400×20000 | 3-5 | 1.5-5 | ≤ 800 | 37 | 18-30 | 60 |
| Φ 3000×20000 | 3-5 | 1.5-5 | ≤ 800 | 55 | 25-35 | 78 |
| Φ 3000×25000 | 3-5 | 1.5-5 | ≤ 800 | 75 | 32-40 | 104.9 |
Applications Of Rotary Dryer
Rotary Dryer, also known as Rotary Dryer,It is widely used in building materials, metallurgy, chemicals and industrial, Rotary dryer is applicable for particle materials, and is also applicable for paste and viscous materials which are mingled with particle materials, or materials whose water content is high. This rotary dryer can dry many kinds of materials which contain moisture, such as coal, coal slurry, slag, industrial waste, and clay stone,Sable
Sand Dryer For Dry Mortar Mixing Plant
Sand dryer is handling by bringing it into direct contact with a heated gas. The sand dryer consists of revolved body, raise material board, transmission device, support device and seal ring etc ,The dryer slopes slightly so that the discharge end is lower than the material feed end in order to convey the material through the dryer under .
Working Principle Of Sand Dryer
Material to be dried enters the dryer, and as the dryer rotates, the material is lifted up by a series of internal fins lining the inner wall of the dryer. When the material gets high enough to roll back off the fins, it falls back down to the bottom of the dryer, passing through the hot gas stream as it falls. This gas stream can either be moving toward the discharge end from the feed end (known as co-current flow), or toward the feed end from the discharge end (known as counter-current flow). The gas stream can be made up of a mixture of air and combustion gases from a burner, in which case the dryer is called a direct heated dryer. Alternatively, the gas stream may consist of air or another (sometimes inert) gas that is preheated. When the gas stream is preheated by some means where burner combustion gases do not enter the dryer, the dryer known as an indirect-heated type. Often, indirect heated dryers are used when product contamination is a concern.
