Loading...
FAQ 2017-05-24T20:12:12+00:00

Do You Have A Products FAQ We Can Help With?

Online Customer Service Q & A
Can we use our own motor for the machine 2017-07-10T17:26:00+00:00

Only OG5040 that you can use your own motor. Other type mortar pump has their dedicated motors.

What is mortar pump the difference between single cylinder and double cylinder 2017-07-10T17:02:03+00:00

Single cylinder pressure fluctuation is large, double cylinder pressure fluctuation is small; Fluctuation little conveying distance long.

Do you have user manual of the mortar machine? How to use it? How to clean it 2017-07-10T15:20:17+00:00

Yes, we have. All can be seen in the user manual, and will send to your email later.

Can the mortar pump be used for spraying 2017-07-10T15:09:31+00:00

Suggested not too high if spraying construction, uniform spray is not easy; The best for inside layer construction. It is ok that spray height of 10 meters; The pipe length is not recommended more than 40 meters; The reason is not pump pressure not enough, but the longer the pipe, the higher the nozzle discharge uniformity more bad.

How long hose does the mortar pump contain 2017-07-10T15:06:50+00:00

OG5040 mortar pump One root 20 meters convey hose.

What is the material of the front blade 2017-07-10T15:02:13+00:00

About the raw material of the front blade, We cooperate with phoenix hardened aluminum, it went through high hardness aluminum oxidation, to ensure the wipe board smooth  without any distortion.in the working process, so can ensure the flatness of the wall

How the machine is working when there is a window on the wall 2017-07-10T15:00:00+00:00

First let the machine stop on the top of the window, then add cement mortar, let the machine work  above the window. Then let the machine work under the window.

Does it needs special materials in the cement mixture in order to wipe it on the wall 2017-07-10T14:58:44+00:00

No need special materials, The mortar is the same as the mortar which by manual plastering wall

Does it need render section joints flatness manually 2017-07-10T14:56:09+00:00

No.Full Automatic .we use rendering panel which can change the angle.

Is there some gaps between one time rendering from another time rendering 2017-07-10T14:54:36+00:00

Max. gaps is only 1-2mm, workers can plaster it smoothly by manual

Does it can be adjustment for render width 2017-07-10T14:53:00+00:00

We have different models with width of 80cm,100cm,120cm, but for one machine,the render width can not be adjusted.

If the wall height is more than 5 meters, what should do 2017-07-10T14:51:55+00:00

Generally speaking, This machine’s standard is for less than 5meters, if more than 5meters, please tell us in advance, we need to special manufacture it for you.

If I want to rendering 3m, 4m, 5m wall, does one set machine be OK 2017-07-10T14:51:05+00:00

Yes,we will send you 20cm,40cm,60cm,80cm ,2m uprights of different length to you after you bought, So you can choose upright according to the height of the wall.

What’s the rendering thickness of the machine? Can I adjust and control the thickness? 2017-07-10T14:49:57+00:00

-Rendering thickness from 2mm-30mm, it can be adjust.

-We use newest Infrared laser leveling way to instead of Making point by manual,just adjust the position of the Infrared laser, making rendering machine far from the wall 2mm to 30mm.

3. What is the ratio of the raw material? Do I have to use ready mix cement, sand and water for this machine? Do you have wet mortar mix machine 2017-07-10T14:48:36+00:00

Cement: sand=1:2

Yes, this automatic rendering machine can’t mix the cement, sand and water, which should be mixed by manual or other mortar mixer machine

If you need to mix cement+sand+water by machine, we have wet mortar mixing machine to recommend

What’s the difference of ORM5, ORM6 and ORM7 2017-07-10T14:47:11+00:00

There are no essential differences, just on request of different customer’s different demand:
1. ORM5 can render from 20cm to 4.5m, rendering width can be 800mm; 1000mmand 1200mm

2.ORM6 can render from 0cm to 4.5m, rendering width can be 1000mm;

3.ORM7 is updating type of ORM5, has same technical parameters of ORM5

Whether can use the hose pump to grouting? How to configure it if can? 2017-07-10T14:44:13+00:00

Yes, but need to know the pressure displacement and medium; The pressure of the pump can realize; if to spray need to add an air compressor.

What is the high temperature that the squeeze tube can withstand? 2017-07-10T14:43:29+00:00

Natural rubber maximum temperature of 70 degrees; Nitrile rubber, epdm maximum temperature under 100 degrees.

What is the wear parts of the hose pump 2017-07-10T14:42:33+00:00

Squeeze tube

What is the manufacturing days of the hose pump 2017-07-10T14:41:34+00:00

Normal 25 working day.

How long is the working life of the hose pump 2017-07-10T14:40:21+00:00

The working life of the general good hose pump in 7 to 10 years.

What kind of machine are there? What is the difference between them? 2017-07-10T14:39:34+00:00

Chain type and Gear type; Difference is Gear transmission is relatively stable, relatively high prices;Chain type economy is applicable.

How much is the squeeze if buy separately 2017-07-10T14:38:05+00:00

This according to the size of the pump, to determine the length, price is given only after that.

Machine with a squeeze tube? And what is the length? 2017-07-10T14:37:13+00:00

Quotation in addition to the machine itself, together with the extra two root squeeze tube, production capacity is different, the length is not the same.

How long is the working?life of the squeeze tube? 2017-07-10T14:27:16+00:00

800-1200hours

 

How long can the hose pump used if it under 24 hours continuous?work? 2017-07-10T14:25:42+00:00

Can work continuously 24 hours, can be used all the time.

What is the material of the squeeze tube 2017-07-10T11:46:12+00:00

General rubber; There are other material, hose depends on customer request, if you want to wear this way to provide natural rubber, if with acid and alkaline supplied epdm, of course the price also is different, but we give you are good, after inspection.

Can you send the outline?dimensional?drawing of the hose pump 2017-07-10T11:37:55+00:00

Yes, it is ok.

 

Your cement hose pump with series reducer 2017-07-10T11:34:07+00:00

There cement hose pump are several kinds of reducer, not just in a series.

Can we equip the Sicoma type mixer onto the plant? 2017-07-10T11:23:14+00:00

Of course,if you need ,we can equip the Sicoma type for you,and Sicoma have the biggest manufacturing base in China and we have cooperated with Sicoma for many years,so we have very good price.

How to feed aggregates? 2017-07-10T11:22:36+00:00

It can feed aggregates by skip hopper or by belt conveyor.The small plant,like 25 m3/h,35 m3/h,and 50 m3/h,feeds aggregates by skip hopper.The big plant,whose capacity is higher than 60 m3/h, feed aggregates by belt conveyor.

What about water & admixture feeding ? 2017-07-10T11:22:00+00:00

There is an annular pipe for water or admixture feeding.

What will be total cycle time-feeding of material,mixing of material,discharging of concrete mix? 2017-07-10T11:21:25+00:00

(we believe that water,admixture,cement & fly ash are also poured parallely while feeding material)
The cycle time is 120 seconds

Can you tell me the brand of the parts you use for concrete batching plant 2017-07-10T11:20:30+00:00

You can see that for every part we use very famous brand,the details is as follow:
All motors of our plant: Siemens Brand Form Germany.
Load cell: Mettler Toledo brand ,from USA
Screw Conveyor: WAM brand form Italy
Discharge Valve: WAM brand form Italy
Air Cyliner: AIRTAC,NO.1 brand in Asia
Electrical Component: Schneider Brand Form Germany
Monitoring System: 4 Cameras with compurter display

How many days it need to install the concrete batching plant? 2017-07-10T11:18:46+00:00

In general,it takes one weeks to istall the concrete batching plant.

 

The concrete shotcrete machine, we can use it directly when we receive it? 2017-07-10T11:02:09+00:00

The concrete shotcrete machine, we can use it directly when we receive it?

Why the wet shotcrete machine cost is higher than dry shotcrete machine 2017-07-10T11:00:40+00:00

Wet shotcrete machine, machine larger, working less dust,smaller noise, environmental protection, spraying effect is better, save raw material.

what is the difference of the dry mix shotcrete machine and wet shotcrete machine 2017-07-10T10:59:37+00:00

Dry mix shotcrete machine: feeding dry raw material into the hopper Wet shotcrete machine, feeding wet raw material into the hopper.
The same. final, spraying out wet concrete.

The dry shotcrete machine, how it’ s work? 2017-07-10T10:53:39+00:00

The dry shotcrete machine working:
1. feeding dry mixture of cement + sand + small stone (less than 20mm), into hopper
2. the machine is rotor structure to make the raw material into convey hose
3. the shotcrete machine, need one air compressor to supply air pressure.
4.the air pressure make the raw material through the convey hose to arrive the spraying gun.
5.in the spraying gun part,. contact water hose and air hose to add water and air pressure,
6.spraying out wet concrete

The shotcrete machine, it will need electric and diesel to make it work 2017-07-10T10:49:10+00:00

The concrete shotcrete machine, we have electric drive type, diesel engine drive type, and air drive type for chioce.

We want to start the business with this type of machines from the most basical models 2017-07-10T10:46:35+00:00

Concrete shotcrete machine We have 3m3/h, 5m3/h, 9m3/h, 15m3/h, 20m3/h, 30m3/h, 40m3/h etc
5m3/h is hot sale on the marketing, and with lower price, so it is suitable for start.

Shotcrete machine, can it be used to building swimming pool and building house 2017-07-10T10:41:32+00:00

Building swimming pool and building house, concrete convey and spraying work, the concrete shotcrete machine is suitable.

What project the machine used for 2017-07-10T10:39:53+00:00

Concrete shotcrete machine, is widely employed in mining, tunnel, culvert, subway, slope protection work,
hydropower engineering, building, underground excavation engineering etc.

 

What are the services after buying the mortar mixer production lines and install it 2017-07-10T10:36:20+00:00

1)With the fastest speed (usually within 1hour except at the weekend or evening in China time Zone)to make the quotation for customers on the prerequisite that we are clear to capacity, quantity,automation requirement, spare parts requirement (Chinese Top Brands or World Grade Brands like Siemens Motors etc), wearing parts requirement,delivery terms etc.

 

2)Turnkey Service

From the design for single machine or plant and civil engineering, making CAD, customers confirmation on CAD, Processing, Manufacturing, Delivery, Installation&Commission,Training,Pre-operation

 

  • Offering the analysis of ROI(Return of Investment).

 

4) 1-3 short training periods, 10-15 days installation,1-2days commission,1-2days pre-operation.

 

  • Total service fees below USD90 for one engineer in one day compared with markets trends USD120.00

 

6) Shortest periods of processing and manufacturing

For single machines, at most 5days;for production line,at most 15days.

 

7) Warranty.

For the host machine, one year (12 months) from the date of the goods leaving seaport.

For spare parts and wearing parts,tailored to customers requirement.

Is the packing weight can be controlled 2017-07-10T10:34:26+00:00

For example, sometimes required to make baking 50kG and sometimes 25kG, … Etc

Yes, this packing machine can packing 10kg-50kg, it is adjustable

What is the capacity of twin shaft agravic mixer 2017-07-10T10:33:35+00:00

1t per batch, per batch will take 3-5mins, the total capacity can be 12-20t/h

 

Is the conveyor controllable 2017-07-10T10:32:42+00:00

No, the conveyor’s speed is not adjustable; if you want to make it,one extra frequency converter is necessary.

 

What is the speed of screw conveyor between hopper and weighing hopper 2017-07-10T10:31:41+00:00

40t/h

 

What is the dimensions of this equipment 2017-07-10T10:28:52+00:00

mortar mixer 8m*8m*8m, it takes at least 80-100m2 to install the equipment.(Different models, different configurations, different sizes)

We offer free onsite design,Provide installation and maintenance equipment services.

How can be add the chemicals? 2017-07-10T10:25:47+00:00

Mortar mixer is a open hole at bottom of bucket elevator,chemicals can be added there

OR Additive weighing system

 

What is the model of mortar mixer production line? 2017-07-10T10:23:16+00:00

Automatic feeding,automatic dosing,automatic loading,automatic mixing,automatic packing(workers need to handle bags)

1-5TPH Small dry mortar mix plant

5-15TPH automatic dry mortar plant

15-50TPH full automatic dry mortar mix plant

 

What is the render height ? 2016-04-25T17:40:09+00:00

It can reach up to 5-6 meters.

How much thickness should be applied? 2016-04-25T17:36:45+00:00

The same principles apply as the way you render by hand. However, if required, RENDERING MACHINE enables you to achieve from 5 mm up to 30mm render.

What finish can be achieved? 2016-04-25T17:30:57+00:00

Depending on how fine or course the sand is, our RENDERING MACHINE can produce smooth and flat render finish.

What is RENDERING MACHINE? 2017-05-19T16:02:53+00:00

RENDERING MACHINE is also called Automatic Rendering Machine, Automatic Plastering Machine, Wall Rendering Machine, Wall Plastering Machine Etc. It is unique and perhaps one kind of automated rendering machinery ideally suitable for the construction/building industry. It works with conventional cement mortar which brings it to a smooth, flat finish with variable and adjustable thickness to suit each application.

What is the total power consumption (KW)of this dry mortar plant? 2016-04-25T17:23:28+00:00

It is about 20-80kw based on the capacity of the dry mortar plant.

What is the area required for this dry mortar plant? 2016-04-25T17:22:37+00:00

According to different capacity, the capacity required 300-1000m2.

What equipment and service you can provide? 2016-04-25T17:21:12+00:00

We can provide you turnkey solution of dry mortar plant from working site planning to dry mortar machines, transportation, installation and training, formula of dry mortars,  after sales services, life time techincal support etc.

How many person required to operate this dry mortar plant? 2016-04-25T17:01:25+00:00

Usually 2-4 workers are enough to operate this dry mortar plant.

What’s the difference between full automatic dry mortar plant and Semi-automatic dry       mortar plant? 2016-04-25T16:59:53+00:00
  • Semi-automatic dry mortar plant is cheaper than full automatic dry mortar plant.
  • Semi-automatic dry mortar plant do not need to equip material silos while full automatic  type equip silos.
  • Semi-automatic dry mortar plant is manual feeding and automatic weighing and packaging, full automatic type can realize automatic feeding and packaging.
How about the investment of this project? 2016-04-25T16:58:19+00:00
  • A: Our engineer can design the dry mortar plant as your requirement and your budget, different tpye   dry mortar plant investment are difference.
  • B:Low capacity low cost, we will provide you cost effective solution as your requirement.
Why Choose Us? 2016-04-25T16:53:51+00:00

1) Excellent mixing performance

2) Highest reliable performance

3) Unique no-sticky shaft technology

4) Accurate measurement accuracy

5) Perfect industrial design

6) Convenient transportation and installation

7) Simple operating performance

8) Good maintenance performance

9) Excellent environmental protection performance

10) TV monitoring system

Get A Quote Today

At vero eos et accusamus et iusto odio dignissimos ducimus qui blanditiis praesentium voluptatum deleniti atque corrupti quos dolores et quas.

FIRST NAME *
LAST NAME *
EMAIL ADDRESS *
PHONE NUMBER

SUBJECT

HOW CAN WE HELP?